My UVerse receivers are wired (coax) and they appear to be working as well (so far). I've connected my Amplifi Mesh HD router and Speedtest on AppleTV connected to the router is showing the same results. I'm getting about 820Mbps down and 860Mbps up when connected directly to ethernet via coax. Quick update - I just installed the Actiontec Bonded MoCA 2.0 adapters and so far so good. As my disclaimer - These steps worked for me, but I don't know enough about coax/electrical/etc to say this it would work for everyone, so use your best judgment before purchasing the items. Please feel free to let me know if there are any further improvements to this I could make. If nothing works, get a cable guy to set up a connection similar to how I have shown it in the attached picture. Lastly, if you have several cable connections a coax connection tester (such as a coaxial tone tester from Holland) would help. The Coax light also takes a few seconds to come on and it does so once a round-trip connection has been established - for those who have not been able to get this to work, I'd suggest trying the round-trip adapter adapter test and if that works, then you may have an issue with the coax cables. The only challenge I had was making sure that the coax cables were connected to one another - when I initially did the setup it didn't work and this was because none of the wires were actually connected in the cable box. My situation was made simpler by the fact that I didn't have any cable connection and got to use the coax network solely for the purpose of making the ethernet network. I know there is quite a bit of confusion online over how it works. This is a very simple installation and just requires connecting wires together to make it work. This should light up the Coax indicators on both the adapters. Router -> Adapter1_Ethernet -> Adapter1_CoaxIn -> Adapter2_CoaxIn -> Adapter2_Ethernet -> Adapter2_Device_Connected_To_The_Ethernet This should establish a link as follows – Connect the Ethernet port of one adapter (say adapter 1) to the router and the Ethernet port of the other adapter (adapter 2) to a device. In order to test whether your Actiontec kit is working, you can connect the Coax In connectors of each adapter together with a coax cable.I was able to obtain the advertised speeds after testing with iperf3 between 2 devices linked via Actiontec in different rooms.This can take 15-30 seconds depending on your coax setup, etc The Coax indicator on the Actiontec adapter will light up only after a bi-directional connection has been established.If the coax cables in the cable box do not have connectors, use a coax stripper to attach connectors (sold at Home Depot / Lowe’s).Coaxial Cable Stripper (Can use any ordinary wire cutter)ġ) Connect Actiontec Adapter 1 in the room (Living Room) with the routerĢ) In the cable box, connect coax outlet from Living Room to the other coaxial cables where you want to provide Ethernet connectivityģ) Connect adapter in other rooms where the coax was connected to (from 2).I took some notes as I set up my environment which I have provided below. It is a shame considering that the product is very capable. You'd think that Actiontec - as the manufacturer would know what they are selling but evidently doesn't. I saw the videos on Youtube and the support documentation which did not ask for a Cable Modem. I called Actiontec and they advised that if I didn't have "Cable Modem" it won't work. The first floor has coax outlets in all the rooms but no ethernet outputs and as a consequence, we were stuck with having a Gigabit ethernet that only worked in a single room. The ground floor is where the router is located. We have been cable-free for some time and hence the cable lines have remained unused. The ONT (Optical Network Terminal) has an ethernet out that goes into the AT&T Router. Had I listened to the helpdesk at Actiontec, I wouldn't have had this today. Most of the new residences in the area now have ethernet wall ports but if you don't you can very well use the Actiontec Bonded Moca 2.0 to get the same benefit.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |